Key Features

Monitor:

up to 1000 feet (305 meters) of conductive fluid sensing cable and/or spot detectors per zone; 6000 feet (1830 meters) total, or

up to 700 feet (213 meters) of chemical sensing cable per zone; 4200 feet (1280 meters) total

The LDRA6 fully integrates with RLE’s family of leak detection cables. One controller can monitor an area for both water and chemical leaks with our distinct leak detection cables.

Create a unique combination of zone leak detection and dry contact alarm annunication

Adjustable leak thresholds fine-tune the system

Supervised inputs monitor cable for breaks and contamination

Form C relay output for each input enables communication with BMS/NMS/BAS via Modbus RTU (EIA-485)

One tri-color notification LED per input, and one audible alarm

Included Equipment: LDRA6 alarm panel

Additional Requirements: Isolated RLE power supply, leader cable, end-of-line (EOL) terminator, sensing cable (as needed for application)

Power: Requires an isolated power supply.

24VDC Isolated @ 600mA max.; requires RLE power supply PSWA-DC-24 (not included)

Inputs

Leak Detection Cable: Compatible with SeaHawk sensing cable and SD-Z and SD-Z1 spot detectors (not included)

Cable Input: Requires 15ft (4.6m) leader cable and EOL terminator for each zone (not included)

Maximum Length: 1000 feet (305m) of conductive fluid sensing cable and/or spot detectors per zone; 6000 feet (1830m) total, or 700 feet (213m) of chemical sensing cable per zone; 4200 feet (1280m) total

Detection Response Time Digital: When used with conductive fluid sensing cable or chemical sensing cable, 20-3600sec, software adjustable in 10 second increments; ±2sec Dry Contact NO/NC.

Outputs

Relay: 1 Form C Summary Alarm Relay, 6 Form C alarms, one per input/zone 1A @ 24VDC, 0.5A resistive @ 120VAC; Configurable for supervised or non-supervised, latched or non-latched

Communication Ports

EIA-232: 9600 baud; Parity none; 8 data bits, 1 stop bit

EIA-485: 1200, 2400, 9600 or 19,200 baud; Parity none, odd, even (programmable); 8 data bits, 1 stop bit

Protocols

Terminal Emulation (EIA-232): VT100 compatible

Modbus (EIA-485): Slave; RTU Mode; Supports function codes 03, 04, 06, and 16

Alarm Notification

Audible Alarm: 85DBA @ 2ft (0.6m); re-sound (disabled, 8,16 or 24 hours)

Visible Alarm: LED: Alarm: red; Cable Fault: yellow

Front Panel Interface

LED Indicators: Power: 1 green (on/off); 1 tri-color Status LED per zone (6 total) (Power On: green; Alarm: red; Cable Fault: yellow)

Push Buttons: Quiet/Test/Reset: 1

Operating Environment

Temperature: 32° to 122°F (0° to 50°C)

Humidity: 5% to 95% RH, non-condensing

Altitude: 15,000ft (4572m) max.

Storage Environment: -4° to 158°F (-20° to 70°C)

Dimensions: 10.5″W x 8.0″H x 2.0″D (267mmW x 203mmH x 51mmD)

Weight: 4 lbs. (1.82kg)

Mounting: Wall mount enclosure

Certifications: CE; ETL listed: conforms to UL 61010-1, EN 61010, CSA C22.2 No. 61010-1, IEC 61326:1997; RoHS compliant

Shop and search results

Introduction

Ever since the first commercial thermal imaging camera was

sold in 1965 for high voltage power line inspections, by what

would later become FLIR Systems, the use of thermal imaging

cameras for industrial applications has been an important market

segment for FLIR.

Since then thermal imaging technology has evolved. Thermal

imaging cameras have become compact systems that look just

like a digital video camera or digital photo camera. They are easy

to use and generate crisp real-time high-resolution images.

Thermal imaging technology has become one of the most

valuable diagnostic tools for industrial applications. By detecting

anomalies that are usually invisible to the naked eye, thermal

imaging allows corrective action to be taken before costly

system failures occur.

Optional VAV Accessories for use with ZN Line modules

The ZASF is part of a family of control modules designed specifically for VAV terminal box applications. It is designed to be used with the ZN341v+ and ZN141v+. It mounts directly on the secondary VAV damper shaft and provides an integral actuator and a second integrated flow sensor for damper positioning and air-flow sensing in dual duct or tracking systems.

Zone Controller

Automated Logic’s ZN220 provides unprecedented power and flexibility through fully programmable networked controllers. The ZN220 controllers connect to the Building Automation System (BAS) network using BACnet over ARCNET 156 kbps or MS/TP. The ZN220 supports a line of RS room sensors using its Rnet port.

Multi-Equipment Application Controllers

M Line controllers are ideal for multi-equipment applications in commercial environments. These robust standalone controllers utilize native BACnet communications over a high-speed ARCNET 156 kbps network to ensure superior performance.

Powerful Multi-Equipment Controller and Router

ME-LGR Powerful Multi-Equipment Controller and Router

Combining the features of our powerful multiequipment controller with a high-speed BACnet® router, the ME-LGR can do it all. Need 100 Mbps communications to a critical control site? Need to control multiple pieces of equipment at that site? Need to integrate third-party equipment on a proprietary network with your BACnet system? No problem. The ME-LGR can do it all, and it can also serve as a router to controllers on an ARCNET 156 kbps or MS/TP network.

Powerful Gateway

Automated Logic’s Equipment Portal (EQ-PRTL) sets a new standard for integrating other manufacturers’ equipment into WebCTRL®. EQ-PRTL is a powerful gateway to a single piece of equipment /device using proprietary or open protocols such as Modbus and LonWorks. Support for BACnet® over ARCNET 156 kbps and MS/TP communications are standard.

Universally Understood Graphical Programming

EIKON-LogicBuilder for WebCTRL is the most advanced graphical programming tool in the industry. With the click of a button, you can build complex control algorithms, diagnose problems, and run real-time or simulated operational data to evaluate the performance of a control sequence. EIKON-LogicBuilder makes it easy to understand control sequences as it does not use cryptic “line by line” computer code.

Key Features and Benefits

Intuitive graphical programming tool eliminates the need for complex programming or cryptic computer code.

Powerful library of microblocks (control functions) provide the flexibility to develop simple and complex control sequences.

Universally understood graphic symbols make control algorithms easy to understand.

Flexible simulation mode enables the user to view the control routines before system installation which simplifies development and troubleshooting.

Live Graphic Function Blocks (GFBs) are a valuable troubleshooting tool that allow system performance to be viewed in real time.

Complete integration with WebCTRL workstation software for seamless facility programming.

Instant project documentation captures development process.

An extensive library of sample GFBs provides pre-engineered solutions to many typical HVAC control applications. They can be used as-is, or easily modified in EIKON to meet special requirements.

Complete compatibility and functionality with BACnet®, ASHRAE’s industry standard protocol, for programming BACnet objects.

Characteristics

Introduction To Building Management Systems

A BMS is most common in a large building. Its core function is to manage the environment within the building and may control temperature, carbon dioxide levels and humidity within a building. As a core function in most BMS systems, it controls heating and cooling, manages the systems that distribute this air throughout the building (for example by operating fans or opening/closing dampers), and then locally controls the mixture of heating and cooling to achieve the desired room temperature. A secondary function sometimes is to monitor the level of human-generated CO2, mixing in outside air with waste air to increase the amount of oxygen while also minimising heat/cooling losses.

Systems linked to a BMS typically represent 40% of a building\\\’s energy usage; if lighting is included, this number approaches 70%. BMS systems are a critical component to managing energy demand. Improperly configured BMS systems are believed to account for 20% of building energy usage, or approximately 8% of total energy usage in the United States.[citation needed]

As well as controlling the building\\\’s internal environment, BMS systems are sometimes linked to access control (turnstiles and access doors controlling who is allowed access and egress to the building) or other security systems such as closed-circuit television (CCTV) and motion detectors. Fire alarm systems and elevators are also sometimes linked to a BMS, for example, if a fire is detected then the system could shut off dampers in the ventilation system to stop smoke spreading and send all the elevators to the ground floor and park them to prevent people from using them in the event of a fire.

Functions of Building Management Systems

The three basic functions of a central, computer-controlled BMS are:

• controlling

• monitoring

• optimizing

the building’s facilities, mechanical, and electrical equipment for comfort, safety, and efficiency.

A BMS normally comprises of:

• Power systems

• Illumination system

• Electric power control system

• Heating,Ventilation and Air-conditioning HVAC System

• Security and observation system

• Magnetic card and access system

• Fire alarm system

• Lifts, elevators etc.

• Plumbing system

• Burglar alarms, CCTV

• Trace Heating

• Other engineering systems

• Home Automation System

• Fire alarm and Safety system

Benefits of BMS

Building tenant/occupants

• Good control of internal comfort conditions

• Possibility of individual room control

• Increased staff productivity

• Effective monitoring and targeting of energy consumption

• Improved plant reliability and life

• Effective response to HVAC-related complaints

• Save time and money during the maintenance

Building owner

• Higher rental value

• Flexibility on change of building use

• Individual tenant billing for services facilities manager

• Central or remote control and monitoring of building

• Increased level of comfort and time saving

• Remote Monitoring of the plants (such as AHU\\\’s, Fire pumps, plumbing pumps, Electrical supply, STP, WTP etc.)

Maintenance Companies

• Ease of information availability problem

• Computerized maintenance scheduling

• Effective use of maintenance staff

• Early detection of problems

• More satisfied occupants

References

Wikipedia