Mechanical Installations

In many industries, mechanical systems serve as the backbone

of operations.

Thermal data collected with a thermal imaging camera can be

an invaluable source of complimentary information to vibration

studies in mechanical equipment monitoring.

Mechanical systems will heat up if there is a misalignment at

some point in the system.

Conveyor belts are a good example. If a roller is worn out, it will

clearly show in the thermal image so that it can be replaced.

Typically, when mechanical components become worn and less

efficient, the heat dissipated will increase. Consequently, the

temperature of faulty equipment or systems will increase rapidly

before failure.

By periodically comparing readings from a thermal imaging

camera with a machine’s temperature signature under normal

operating conditions, you can detect a multitude of different

failures.

Suspected roller Overheated bearing

This thermal image shows an electric engine under normal operation.

Motors can also be inspected with a thermal imaging camera.

Motor failures like brush contact-wear and armature shorts

typically produce excess heat prior to failure but remain

undetected with vibration analysis, since it often causes little

to no extra vibration. Thermal imaging gives a full overview and

allows you to compare the temperature of different motors.

Other mechanical systems monitored with thermal imaging

cameras include couplings, gearboxes, bearings, pumps,

compressors, belts, blowers and conveyor systems.

Examples of mechanical faults that can be detected with thermal

imaging are:

• Lubrication issues

• Misalignments

• Overheated motors

• Suspect rollers

• Overloaded pumps

• Overheated motor axles

• Hot bearings

These and other issues can be spotted at an early stage with

a thermal imaging camera. This will help to prevent costly

damages and to ensure the continuity of production.

Motor: Bearing Problem.

Motor: Internal Winding Problem.

References: Flir Systems

Electrical systems

Thermal imaging cameras are commonly used for inspections of

electrical systems and components in all sizes and shapes.

The multitude of possible applications for thermal imaging cameras

within the range of electrical systems can be divided into two

categories: high voltage and low voltage installations.

High voltage installations

Heat is an important factor in high voltage installations. When electrical

current passes through a resistive element, it generates heat. An

increased resistance results in an increase in heat.

Over time the resistance of electrical connections will increase, due

to loosening and corrosion for instance. The corresponding rise in

temperature can cause components to fail, resulting in unplanned

outages and even injuries. In addition, the energy spent on generating

heat causes unnecessary energy losses. If left unchecked, the heat

can even rise to the point where connections melt and break down; as

a result, fires may break out.

Examples of failures in high-voltage installations that can be detected

with thermal imaging:

• Oxidation of high voltage switches

• Overheated connections •

Incorrectly secured connections

• Insulator defects

These and other issues can be spotted at an early stage with a thermal

imaging camera. A thermal imaging camera will help you to accurately

locate the problem, determine the severity of the problem, and

establish the time frame in which the equipment should be repaired.

A wide view of a substation can quickly show areas where unwanted high

resistance connections exist. No other predictive maintenance technology is

as effective for electrical inspections as thermal imaging.

One of the many advantages of thermal imaging is the ability to perform

inspections while electrical systems are under load. Since thermal imaging

is a non-contact diagnostic method, a thermographer can quickly scan a

particular piece of equipment from a safe distance, leave the hazardous

area, return to his office and analyze the data without ever putting himself

in harm’s way.

Thermal imaging cameras allow you to inspect high voltage installations

from a safe distance, increasing worker safety.

Continuity is very important to utilities since many people rely on their

services. Therefore thermal imaging inspections have become the core of

utility predictive maintenance programs throughout the world.

Thermal imaging cameras are used for inspections of electrical systems and

components in all sizes and shapes and their use is by no means limited to

large high voltage applications alone.

Electrical cabinets and motor control centers are regularly scanned with

a thermal imaging camera. If left unchecked, heat can rise to a point that

connections melt and break down; as a result, fires may break out.

Besides loose connections, electrical systems suffer from load imbalances,

corrosion, and increases in impedance to current. Thermal inspections can

quickly locate hot spots, determine the severity of the problem, and help

establish the time frame in which the equipment should be repaired.

Examples of failures in low voltage equipment that can be detected with

thermal imaging:

• High resistance connections

• Corroded connections

• Internal fuse damage

• Internal circuit breaker faults

• Poor connections and internal damage

These and other issues can be spotted at an early stage with a thermal

imaging camera. This will help to prevent costly damages and to avoid

dangerous situations.

Whether you intend to use thermal imaging cameras for

low voltage inspections in production plants, office facilities,

hospitals, hotels or domestic residences, FLIR Systems has

exactly the right thermal imaging camera for the job.

References: Flir Systems

List Price: $0.00

Our Multi-Circuit Monitor power monitoring system provides a convenient solution for monitoring multiple electrical services which share a common voltage source. It also reports diagnostic information such as power factor, volts, amps, and kVAR, over an RS-485 network using the industry standard Modbus® communication protocol. To protect valuable equipment, it has built-in alarm registers for over- and under-voltage, current, and kVA.

The monitoring capabilities and open systems compatibility of the H8238 make it the ideal power monitoring solution for OEM, tenant submetering applications, and load management of power distribution units commonly used in internet data centers. The meter is a UL508 open type device without enclosure.

APPLICATIONS

Tenant submetering

Real-time power monitoring

Activity-based costing

Managing loads

Monitor power parameters from up to 8 services with one device

Save labor and installation costs by monitoring up to eight 3Ø, (or six 3Ø plus neutral current) loads from a single service with common voltage connections

Eliminates the need to install multiple transducers – fewer components to install…saves time and space

Easy connection to up to 24 industry standard five-amp CTs

Modbus communications for efficient data collection

Improve monitoring system efficiencies by accessing 26 data points per circuit, plus alarms, with one RS-485 drop

Daisy chain up to 30 units on a single drop…easy wiring

Field-selectable address, baud rate, parity and wiring connections…simple configuration

The AMR (auto meter reading) is an I/O module that has been specifically designed for the special needs of auto meter reading applications. The AMR can be interfaced directly with the output of various types of pulse output meters (electricity, water, gas, BTU) and the data collected from the various meters sent to a central host via its RS485 interface. Some special features which distinguish it from regular I/O modules are:

– noise filtering from the pulse input to prevent miscounts

– EEPROM memory to retain count data in case of power interruption

– accommodates up to 16 channels of pulse input

– dry contact channel input that eliminates the need for additional power supply

– synchronize retain count with actual meter display

– rechargeable battery backup option to maintain at least 8 hours of continuous operation during a power outage

and many more!

Powerful Microprocessor-Based Lighting Control Panels

Automated Logic’s Lighting Control (LC) line brings the power and simplicity of WebCTRL® to your building’s lighting systems. The LC line utilizes advanced microprocessors to provide superior lighting control, while delivering the rapid response required by lighting applications.

Rugged Flexibility for Single Equipment Applications

Automated Logic’s powerful SE line provides a rugged solution for single equipment applications. Designed to operate in a wide range of environmental conditions, SE controllers can be used in rooftop units, mechanical rooms, equipment closets, or almost any other weather tight location. Fully programmable using the EIKON® graphic programming language, SE controllers use native BACnet communications over either a high-speed ARCNET 156 kbps network or a medium speed MS/TP network to provide maximum flexibility and interoperability.

Powerful Multi-Equipment Controllers

ME 812U Line – Powerful Multi-Equipment Controllers

The ME812U controllers have the speed, power, memory, and I/O flexibility to handle the most demanding control applications in the industry. Capable of controlling multiple pieces of equipment simultaneously, this robust BACnet controller can support complex control strategies with plenty of memory for trends, and is capable of third party integration using other communication protocols.

Powerful Gateway

Automated Logic’s Equipment Portal (EQ-PRTL) sets a new standard for integrating other manufacturers’ equipment into WebCTRL®. EQ-PRTL is a powerful gateway to a single piece of equipment /device using proprietary or open protocols such as Modbus and LonWorks. Support for BACnet® over ARCNET 156 kbps and MS/TP communications are standard.

EIKON®-LogicBuilder for WebCTRL®

Universally Understood Graphical Programming

EIKON-LogicBuilder for WebCTRL is the most advanced graphical programming tool in the industry. With the click of a button, you can build complex control algorithms, diagnose problems, and run real-time or simulated operational data to evaluate the performance of a control sequence. EIKON-LogicBuilder makes it easy to understand control sequences as it does not use cryptic “line by line” computer code. Key Features and Benefits

• Intuitive graphical programming tool eliminates the need for complex programming or cryptic computer code.
• Powerful library of microblocks (control functions) provide the flexibility to develop simple and complex control sequences.
• Universally understood graphic symbols make control algorithms easy to understand.
• Flexible simulation mode enables the user to view the control routines before system installation which simplifies development and troubleshooting.
• Live Graphic Function Blocks (GFBs) are a valuable troubleshooting tool that allow system performance to be viewed in real time.
• Complete integration with WebCTRL workstation software for seamless facility programming.
• Instant project documentation captures development process.
• An extensive library of sample GFBs provides pre-engineered solutions to many typical HVAC control applications. They can be used as-is, or easily modified in EIKON to meet special requirements.
• Complete compatibility and functionality with BACnet®, ASHRAE’s industry standard protocol, for programming BACnet objects.

WebCTRL® Environmental Index™

Balancing Efficiency with Comfort

As energy prices continue to soar, facility managers are under increasing pressure to find ways to cut building operating costs. A simple solution would be to decrease energy consumption, but smart managers know that sacrificing comfort for energy savings could lead to even bigger financial problems. After all, studies have shown productivity decreases as comfort levels decline, leading to lost revenues in companies and difficult learning environments in school systems. What’s needed is a way to measure comfort, so managers would know exactly how far to cut energy usage without negatively impacting comfort. Automated Logic’s Environmental Index provides the solution. Since the key component of comfort is temperature, ALC’s index starts with assigning point values based on the difference between zone temperature and heating and cooling set points. Other factors, such as humidity and CO2 levels, can also be computed into the numeric system to reflect one “comfort” score for all factors. This is a powerful tool for facility managers who need to identify buildings with performance problems or ensure buildings don’t become less efficient as changes are made.